Flashing stock firmware is pretty easy and simple using SP FlashTool. The tool works specifically for MTK (Mediatek) device.
Download the files below and follow the later instructions to learn how to use SP Flashtool to flash stock ROMs on supported devices.
Downloads Options
| Tool | Link |
|---|---|
| SP Flashtool v5.1952 (Windows) | Download |
| SP Flashtool v5.1952 (Linux) | Download |
| Mediatek VCOM Drivers | how to install |
How To Flash With Sp FlashTool
Step One:
Download and install drivers for your device. If you can’t find your device driver, us this guide to download and install the driver.
Step Two:
Download Sp Flashtool and the your phone’s firmware package. (Firmware list)
Step Three:
Extract Sp FlashTool and your firmware package to different folders.
Step Four:
Open SP FlashTool folder and launch SP Flashtool.exe as Administrator.
Step Five:
Click on Scatter-loading, browse and select scatter file from the folder you extracted the downloaded firmware.(e.g, MT6582_Android_scatter.txt)
Step Six:
Click on Download and connect the device to PC via USB cable. Device must be turned off, before attaching to pc.
Step Seven:
Once the device is connected to PC, a progress bar will start loading. Wait for it to complete. A green circle with Ok should popup to indicate completion.
Step Eight:
Disconnect the device and perform a factory reset before you power on fully. Done.
If you still have questions, please ask in comments. Need your device stock firmware? request in comments too.
I am facing issue with my HTC desire 628 phone. Recently i tried to flash the rom with SP flash tool. (download + format). i downloaded the flash file form this link. But now my phone is not starting. (it is only showing charging indication orange light) when i connect the phone with usb cable, it is connecting & after while disconnecting. this is looping. I tried to flash again with the SP flash tool. but is is giving error code 2004. Appreciate your help to resolve this issue. i have doubt that the firmware file i downloaded. Appreciate sharing workable firmware for the same model. (CID-HTC__060, LK-1.01.0000, OS-1.17.400.1)
Thanks in advance
Sorry, Link mentioned in above post.
https://mega.nz/#!wUhnELSK!esO04wjDMouK-WlWY_k7ALq3IaAvtMsAO0XoHEjVf3E
First off, I don’t think you downloaded that SP Flashtool firmware from leakite.com. We don’t have one for HTC Desire 628, but only have firmware you can install via sdcard. See here
Are you able to boot the phone to fastboot mode when you hold Volume down and Power buttons?
Is your phone dual or single sim?
Thanks a lot for your prompt response. My phone is dual sim. May be i have downloaded SP flash tool from somewhere else. I am struggling with this phone almost 3 days. Due to corona virus issue, my country is lock down. Not possible to buy a SD card. Appreciate any help to flash my phone via PC. Fastboot mode is not appearing now.
At this time the only files I have for this phone can be flashed either via Sdcard or fastboot..if you can’t boot to fastboot, I think that’s a little problem.
Thanks. Currently my phone is not switching on. ( i have format it from SP flash tool) Still is it possible to flashed via SDcard. If i found a SDcard. Appreciate if you can guide me how to flash via SDcard.
am new to these technical issues, guys i need support. if you are good and you wish to help me, please check me on [email protected]
Thank you.
Is there another way to flash techno s1 phone without using a PC.
You’d have to get a different firmware- compatible with stock or custom recovery. Otherwise, no!
Pas mal
I means if i can use sp flash tool to flash all mtk phones
No, you cannot! Only firmware that contains a scatter file (usually ends in .txt extension) can be flashed from SP Flashtool.
can i use sp flash tool to all mtk phones
Hi ,
I need firmware for my Lenovo Ideatab S5000-H MTK8389
and thank you so much
Check here – https://www.leakite.com/lenovo-ideatab-s5000-h-wifi3g-official-firmware-flash-file/
password to extract Mobicel_Onyx_V1.2
The password is there on the page. Just copy and paste the link into the password field- the firmware will extract.
password for
Mobicel_Onyx_V1.2
hi collins….
how do flash my huawei y360 u31 using an sd card
This post answers your question – https://www.leakite.com/no-password-download-huawei-y360-u31/
Comment Text*can i use the system update for gionee p4 to install the package from the sd card? As in the firm ware?
It all depends on the firmware you downloaded. If it’s an OTA (sdcard ROM), then yes. But if it contains a scatter file, No…you’ll have to flash via supported tool.
I’m having problems with alcatel 8063 when I turn it on it asks for wifi and then asks for the last synced google account, it also displays android errors. I have downloaded everything needed for flash tool but I cant seem to connect the tablet with the flash tool to start the process. I have tried everything. Any ideas what I’m doing wrong? Cheers
Did you install the required drivers on your PC?
What is the flash file for an n960 tablet ( mt 6582 )
Hi, flashing went well on my Vmobile A10 but after turning it on, the display shows vertical colored lines and does not work.
Now not having saved the phone data, I kindly wanted to know where to download the TWrP recovery of the aforementioned phone. thank
My techno camon c9 has accepted the full process of flashing. i used the flashtool and it even brought the downloaded box. but when i tried to boot it on it hangs on the word camon and as not yet opened. what maybe the problem Collins
It seems you’re flashing the wrong firmware. Have you tried another file?
My infinix note 5 stylus has turned off after updating it can I format it to work again
Yes. But if after factory reset it doesn’t work, download the flashtool firmware from this link and re-flash the phone. https://www.leakite.com/infinix-note-5-stylus-x605-firmware/
Bonjour comment obtenir le firmware de TECNO/VP510/TECNO-F1-PRO 8.1.0/011019/EFG-181123V6
what is passward for mobicel m1000 firmware
The password is on the firmware download page here – https://www.leakite.com/download-mobicel-m1000-stock-firmware-flash-file/
Just copy and paste the text in password field.
peco ajuda meu smart kicka 3 vdf 210 depois de fazer todo o processo de flash deixou de ligar. o que faco?
Com qual arquivo você exibiu?
my teckno has completed flashing process but stil not turning on please help me sir
What is the phone model? Did you try another firmware?
hello
infinix x552 success flashing sp flash tool the green completion circle appears and still the phone doesn’t boots up
please help sir
pls . sir my tecno camon c7 hang on logo pls help me
Have you flashed the phone with a compatible firmware?
je viens de telecharger le fichier de tecno j8 de votre site apres avoir flasher le phone avec le phone refuse de s’allumer aucun .une fois j’essaye de faire la lecture des info phone damage please help
Avez-vous vérifié le numéro de construction pour être sûr de vous flashé sur la bonne variante? La construction que nous avons ici est H354-C1-L-xxxxxxxx.
Aussi, avez-vous pris note des détails de la construction / version de la télécaboration par téléphone par téléphone?
nem lehet letölteni
sir i have alps s7 mtk 6580 i tried some frimware available diffrent websites but they are not workig after completion flashing my phone front camera flash light going on and phone does not starting only black screen sowing no logo no vibrate please help me and does not conecting to pc conecting then automaticaly disconecting after 3 second.
You have these issues because you have not flashed the correct firmware yet. If you can’t find any good firmware currently, try to backup firmware from another working Alps s7 and flash on the faulty one to fix it.
Hola.
Le agradecería en gran manera si me comparte el firmware para el ZTE Blade V8 SE; no lo he podido encontrar para México.
Saludos y éxito en todo.
Actualmente no tenemos ningún firmware de flashtool para ZTE Blade V8 SE. No para cualquier región o país en absoluto. Sólo los archivos de actualización de recuperación de valores que tenemos.
is factory reset necessary after flash
Not always! But if you selected ‘download only’ in SP flashtool before you flashed your phone, sometimes factory reset helps boot the phone properly if its stuck on boot logo. This happens with ‘dump’ or backed up firmware.
When i run the flashtool and want to apply the scatter-file, i’ll get a runtime error from microsoft visualC++ and the programm stops.
I am using an hp probook 6550b with windows 10 and want to restore an alcatel 8063 tablet pixi 7
I have three questions: Do you have Microsoft visual C++ library installed on the PC already?
Does the folder name contain special characters? Are you using latest version of SP flashtool?
Thanks for the quick reply!!
1. i dont know for sure. The programm Visuel C++ is installed on my computer. is that what you mean?
2. It had only one space in the folder. i have removed it . ( it was sp flash, it is now spflash)
3. No, i didn’t use the newest version, cause my laptop is an old one. I thought it would work for sure. Should i try the newest version?
Try using most recent SP Flashtool.
done that, still the same. I stil get this message:
Microsoft visual C++ library
runtime error
Program: C:\spflash\SP_Flash_Tool_v5.1844_Win\flas_tool.exe
This application has requested the runtime to terminate it in an unusual way
and then the program stops
If you can, please try using another computer- to help troubleshoot the issue. Also, you should update your Microsoft visual C++ library following instructions here
Thanks so much for this guide. It’s very straightforward and easy to understand.
The SP Tool says that my MT6580 scatter TXT file from the Doogee X5 ROM is not valid, what do I do?
You have to manually edit the scatter file to remove some text/characters causing the error.
See this video to guide you through the process- https://youtube.com/watch?v=n-m-TqDQcFk
what firmwareflash file that can be use to flash zte b2017g
Sorry, we don’t have a flashtool file for ZTE B2017G.
This is helpful
hi guys i want firmware for vfd 210 that has been extracted from working vfd 210 phone. i formatted my phone and then i download its firmware from this website but its failing to finish flashing may you kindly help me.
Sir, I do have a NOKIA 1 TA 1056 MT6737M
Went boot looped after an OTA UPDATE ((at the condition being used for weeks by installed twrp and bootloader unlocked)) , tried few firmwares ((so called)) which were available in many pages.
In short, now I’ve lost TWRP also, ITS DEAD BRICK. Please help me… I can work with SP flash tools, But I couldn’t find a GENUINE ROM for my phone.
Can you tell me the firmware versions you tried and what happens after you flash them?!
hello i need w3 h806 A2 firmware,,i didint find it on your list there
my tecno w4 is not powering off for to take downloading and usb not recognized help please
Did you install the required drivers on your PC?
what firmware can i use for vodaphone custom rom for tecno n8r
tnks bru it works ahaha nc nextbook NX700QC now is ok..no mre bootloop
Cool…?
Please help me to by pass FRP ON INFOCUS M680 phone
el link para el zte blade s6 esta con error porque borraron los datos de la pagina, sera que pueden conseguir el stock rom para ese modelo y por favor que tenga los archivos scatte.
gracias por el apoyo
¿Me puede decir el enlace específico, por favor, así puedo averiguar qué es exactamente lo que está mal? Además, el firmware que tenemos aquí no contiene archivos de dispersión. solo se puede flashear a través de una tarjeta sd.
Hello Collins… I have a fero iris… recently, it was consuming much of the battery, so I decided to hard reset it. Instead of booting in recovery..I booted factory mode and mistakenly cleared the emmc…. Now phone says invalid IMEI..no signal at all. Wi-fi and Bluetooth work well. What can I do? I have the firmware
Have you tried flashing the firmware to see if the problem is solved?
Need a step by step guide.pliz help
can flashing unlock an airtel only phone to use any line?
It all depends on the device and firmware.
hi i download this firmware(tecno wx4 pro ) but sp flashtool erorr:
chip type not match
i search hardware wxpro 4 and chipset is: mt6737m
but in firmware scarllet is mt6735m
my device is break can you help me ? thanks
SP Flashtool – Download (Windows)
SP Flashtool – Download (Linux)
Mediatek Drivers – how to install
Estan rotos
Todos los enlaces han sido actualizados. ¡Puedes intentar descargar nuevamente!
password for rar file
What file please?
Hi, I need a firmware for my samsung galaxy J5
Model number: SM – J500H
Please..
Download the firmware from here.
PLEASE IT SAYS BROM ERROR ON MYPHONE MY36
Please i insert a memory card to my infinix hot 5 lite and its now hang and off anytime i onn it, it will be showing infinix start up logo , they have tried different files but no progress pls wat should i do
Do you still have the memory card inserted? What files did you try?
please boss, i recently flash my viwa p2 phone and after a successful flash the screen turns black and doesn’t show anything. you can hear the booting sound but nothing appears on the screen. my phone is viwa P2 with fingerprint feature.
It seems you flashed an incorrect firmware. Where did you download this file?
hiii. my name is deep,
I have know how to use sp tool and I already flash roms many time In my oppo find 5 mini
but last time I flash with bad rom and as soon as my phones usb connection was damaged……..it was not connected with pc …….it take much more time to charging……..so that usb problem I will not capable to flash with stock rom …………. so now how can solve this shit……………help me sir………
Download the official firmware from this link and try flashing via stock recovery – https://www.leakite.com/2017/07/download-oppo-find-5-mini-official-firmware-update.html
Hello,I have oppo R827
I have already many times install roms with use of sp tool but last time I install bad rom so my mobile face me problems like…..it not connected with pc ……it takes too much time in chargeing ……….i will not re-install rom because usb connection not work ……….I think usb divers are removed from my phone ……. how can I fix this…….help me
Uninstall and reinstall vcomm drivers on your PC then try flashing again.
Hello Mr Collins. Please i need link to download stock rom for my tecno c9. Thanyou
Follow this link to download the firmware – https://www.leakite.com/2017/06/tecno-camon-c9-firmware.html
Bro the firmware folder can’t be extracted fully as it says it contains corrupted files. Please cross check bro.
While I check the file, can you confirm that it downloaded correctly and completely on your end?
No scatterfile for myphone agua iceberg mini
Please i need software for G-TiDE G21 TAB MT6580 5.1
Hi Collins, my phone’s touchscreen isn’t working at all after stock firmware flash. The phone is S-color Phone X( looks like a clone of iphone x). I have a tried flashing with a few other stock roms from other websites but none of them seems to fix it. I have done a lot of research on google, but the phone is an unkwown chinese brand. Also this phone came without a recovery mode ,so i tried to flash a custom twrp recovery, that’s when everything went haywire, the phone went into bootloop. Some people said that the touchscreen drivers are unsupported and that I shouldn’t have flashed the preloader, but I had no idea about it until now.
So please help me fix this man..
Now I can’t turn on the usb debugging(No touchscreen), can’t connect a mouse via otg. The phone turns on and the volume and power buttons work perfectly.
The phone doesn’t have a recovery so can’t wipe cache/dalvik ,wipe data etc.
Now that you’ve already flashed all the firmware content (also tried other firmware), you can’t just get it fixed by wiping via recovery mode. You need a very compatible firmware with perfectly matching drivers to fix it.
Which flashing mode did you select in SP Flashtool?
I tried both download only and format+download modes. The touchscreen issue started when I used the download only mode.
I finally got into stock recovery. I tried wiping cache, data etc. Nothing works.
Now I can go into fastboot mode through recovery and I had already unlocked bootloader before the touchscreen issue.
Is there any way I can tweak the touchscreen drivers through adb?
Hi Collins,
I flashed my Umi London with the exact stock rom, but when I turned on the phone it refused to come on. The battery is fully charged and I have flashed it 3 times but isn’t coming on.
What have I done wrong? Please help.
What was the condition of the phone before you flashed it? Also, have you tried flashing another firmware besides the one you already have?
after extracting my itel1516plus firmware I couldn’t find any scatter file..please how can I get the scatter file for my phone because it got tripped off and refuse to on again…please I need your help urgently.
Hi Austin, Itel 1516 Plus is a Spreadtrum device, not Mediatek. You can only flash it’s PAC firmware package via Research Download Tool (or other tool that supports SPD devices).
You can find the download link for the tool and how to use it here.
Wat about camon cA6. I tried to flash d phone but it keep showing me erro. Dnt knw yyy. Pls need help for dix
What kind of error is shown on your screen?
s109,s112,s114 these flash files not work.i try allrady.
can you send me lava iris x9(H002_INT/S110) FLASH FILE.
Perdon se me olvido desir que mi ZTE Blade L110 es empresa CLARO
Hola Jorge!
Primero, Blade L110 no es un dispositivo Mediatek (MTK) sino Spreadtrum (SPD) por lo que no puede flashearlo con esta herramienta. Siga el siguiente enlace para descargar el firmware de PAC para su Blade L110 y aprenda cómo flashearlo a través de la herramienta de descarga de investigación.
ZTE Blade L110 enlace: https://www.leakite.com/2018/01/zte-blade-l110-firmware.html
tengo un ZTE Blade L110
ya tengo mi Flash tool pero el Rom o Firmware que descargue y los que he visto no traen el SCATTER que me solicita mi Flash Tool me podrian apoyar creo que ya solo eso e hace falta.
Hey guys I followed all the steps to flash a tecno camon cx air buh whenever I connect after pressing the download its says “can’t find chip bandwidth” then when I try again it says ” the device was turned on too early” so I really don’t know if it’s my USB cord or the phone
1. Ensure that the device is turned off before connecting to computer
2. Try other USB port on your computer. If you think the USB cable is faulty, try another cable.
3. Check that you have properly installed the required drivers. If unsure, reinstall.
4. Follow the instructions above carefully, and be sure you’re not missing any step.
i need your help guys,all i need is password for tecno s1 firmware file
The password is on the same page where your downloaded the firmware (after the ad). Here –
Password: mwate0754
What device is listed in Device Manager? Should it be VCOM or ZTE DFU under com ports?
hi.. I tried to load the map file but keep popup:
“Error: Initializing scatter file failed. Please check the name of scatter file which you load is legal.”.
Downloaded stock ROM for Blackview BV9000 Pro.. Please assisit
Did you download the firmware from Leakite?
Hi Colin,
I`m sure your pretty busy helping lots like me, the problem I have is:
Loaded twrp; all ok, but when I try to sideload a file with adb and twrp set to side load, download starts, twrp fails, invalid zip error, makes no difference if .rar, or zip, tried several different roms, stock rom and others, none will load, and phone reboots, loops.
Swtich off, tried several times to get the phone into fastboot, simply reloads twrp !
Tried sp flash tool but fails to do anything after selecting the scatter file, then plug the phone, seems to recognise phone, but just sits there doing nothing for some time, reloaded usb vcom drivers, sp, com ports sp shows no com, also error h/w borm, and cable check, used different cables and pc, still fails !! any advice would be useful, so if you have time, thanks in advance.
Please provide details of your device, and the version of Windows you use.
Hi, thank you for your reply;
Phone details; Oukitel U20 Plus,MTK 6737T,
Op Sys windows 7, sp1
Mediatek driver 5.632.000
SP Flash tool v5.1804
I have tried closing down virus tools, bluetooth, and other progs, but this makes no difference, also although everything appears to be in the phone memory, all folders show empty !? maybe I`m looking for something in the wrong way,
Thank you again for your reply
If the drivers properly installed, the PC should detect your phone easily. Did you try booting fastboot from TWRP?
If there’s no COM Port shown in SP Flashtool, then it cannot flash as it means no device is connected.
When connecting to SP Flashtool, did you switch off the device?
Hi,
after loading the scatter file, used the download button, then connected the phone, still no com port showing in SP though, but baud rate shows 115200 even if I remove and reinstall SP, used Mediatek_USB_Driver_Auto-Installer_5.1632.00 to install drivers, but none show in device manager, all drivers show in the folders ?totally cant figure this out.
Do I need to find new drivers ? install individually through device manager, if I run adb devices from cmd it shows phone loaded, but windows seems to look for and try to load drivers when sp starts to run, very frustrating, but have lots of patience !
once again thank you for the help
ADB uses a different driver, so it’s possible that it works just fine. Did you try booting fastboot via ADB? (adb reboot bootloader)
I think you should manually install vcom drivers for SP Flashtool, then try flashing again. Please see instructions here
Hi,
just to let you know problem solved, problems are perhaps as follows;
When removing and reinstalling SP, the programe leaves information in the registry (win), by going through and deleting all references, then shut down and reinstall, it appeared to solve the problem.
also I found that if I plugged the phone in before using SP, then held the on+vol Down it ran the scatter and loaded the files, minor prob though, IMEI is missing, but think that can be cured with Maui meta
.Thank you for all you time and help, hope I dont have to bother you again, so thanks for everything
Thanks for sharing this info with us, Rob. I’m sure it’ll be useful to someone. Glad you solved the issue ?
il y a pas un autre moyen pour flasher?
oui ‘jai essayer plsusieurs fois mais a chaque fois que je branche le portable ça se charge
svp aider moi
En fait, Tecno Boom J8 est un appareil Mediatek MT6735. Avez-vous essayé de clignoter l’appareil de toute façon, quelle que soit la fausse (je pense) indication du chipset?
Désolé pour la réponse tardive, a dû s’occuper d’autres problèmes!
. J’ai fait la réinitialisation d’usine et depuis tout ce que je reçois est l’écran BOOM
clignotant comme si elle veut démarrer
J’ai fait la réinitialisation d’usine et depuis tout ce que je reçois est l’écran BOOM
clignotant comme si elle veut démarrer c’est pour ça je veux Flasher. mais ça marche pas
avec sp flash tool biensur sur mon ordinateur
Avez-vous installé les pilotes fournis?
oui coorectement…..mais jai constaté que quand je branche le telephone a l’ordinateur ça commence a se charger et le périphérique apparait dans l’ordinateur et met MT 65xx Android Phone……….or voici le fichier scatter que jai retrouvé pour la tecno boom j8 :MT6735_Android_scatter.txt.
oui coorectement … ..mais jai marque que quand je branche le téléphone à l’ordinateur ça commence à se charger et le périphérique apparait dans l’ordinateur et met MT 65xx Android Phone ………. or le fichier scatter que jai retrouvé pour la tecno boom j8: MT6735_Android_scatter.txt.
svp jai un probleme. jai suivi tout les démarches pour flasher mon tecno j8 mais ça ne marche pas la barre ne dermare pas
I’d like to know whether it may work on Ubuntu Linux OS.
Thanks, I’m ready to read about at the email address already specified as the sender (addresser).
Yeah! I just added Linux compatible version of the Flashtool.
how fix may phone.. flare j2s cherry
can’t turn on, after used sp flash tool..
please help me
whenever you do help me bro its very urgent
please can I get the Stock ROM for an Android device, called TOUCHING T3, I’ve searched every where but I can’t find it
We don’t have this firmware at this time either. You’ll be notified once we do!
please any news about the TOUCHING T3 stock ROM? THIS IS ITS build number C5_72KK_KK_3GW_B15_EMMC_32_4_FWVGA_JJX_G24_B1_TOUCHING_20171122.150716
After flash this firmware my g tide e520 device not power on or no charging (what i do) help me plzz ……. Hurry up
Did the flashing process complete successfully? Is the device still detected by your computer?
Please i cant find the firmfare that can locate my BB chip. My phone is oukitel u20 plus, and there different types of oukitel u20 plus,and i also noticed the BB chip for the different types vary. my BB chip is mt6737t, kernel version is 3.18.35, andriod 7.0. I ended up downloading a firmfare for oukitel u20 plus but that didnt match my BB chip. Please help
Hi Babs, we have firmware for all the variants of Oukitel U20 Plus. Please visit the link below and choose the right firmware for your device from the four files provided.
Link- https://www.leakite.com/2017/06/oukitel-firmware.html
Check the firmware details and confirm on your device before downloading /flashing.
sir my phone Videocon v502430 blank and blue display plz hep me
My phone is a vodafone smart ultra 7 and i have followed the whole guide, it is asking me to select the rom, what do i do?
When you unpack the contents of the firmware you want to flash via SP Flashtool, there’s a .txt file (usually something like MT65xx_scatterfile.txt).
You are to click on Scatter-loading from SP flashtool display, and select the .txt file before you proceed with the other steps to flash.
My phone is hanged it did not any sign of the starting pls tell me how to restart the my phone
If it’s stuck and doesn’t want to reboot, just hold Power button and Volume Down for at least 5 seconds and it will shutdown.
If what you mean is that your device can’t turn on at all, what’s the device name and model?
Techno J8 Boom
Download and flash official Boom J8 firmware from this link to revive your device. https://www.leakite.com/2016/12/tecno-boom-j8-firmware.html
im using Tecno J8. i did factory reset and since then all i get is the BOOM SCREEN
flashing as if it want to boot
Did you flash any firmware after factory reset, or just that?
Hi
i have the same bland with the same problem what can i do?? i am real confused since i experience such problem,
The phone was working ok, I had used it to navigate Facebook a few times previously. The backlight and a quick vibration is all I get.
Try flashing with SP Flashtool again, but this time select Format All + Download and not Download Only.
Tried with “format all+download”, Flash Tool said OK. Disconnected from USB cable and pressed power button. Quick vibration and backlight same as before. Plugged it back into USB cable after a few minues of inactivity, now Windows doesn’t see it at all. Is there anything else I can try with the Flash Tools application? It’s clearly not hard bricked but I’m out of ideas myself!
I would advice you to use the sdcard firmware at this stage. Download the first package (912 MB) and copy to an sdcard.
Download and flash this twrp recovery- https://yadi.sk/d/HwqlVzWM3HmNVQ. Extract the scatter file you currently use, to a folder separate folder with the twrp recovery then flash.
Disconnect phone from PC now and use volume + Power button to access twrp. Select Install Zip, navigate to where the firmware is and select it to flash. In most cases, this works just fine.
If it doesn’t flash via twrp, copy stock recovery.img from the firmware folder to sdcard. Boot twrp again flash the IMG file from there. Reboot recovery now and select the sdcard firmware to flash.
Let me how this turns out!
Unfortunately the recovery screen isn’t appearing, although I can tell it’s in there somewhere because pressing the buttons results in a short vibration. Still a blank lit screen… Thanks for trying to help, Collins. To get it looked at would cost me more than the phone did, so I’m probably going to bin it. 🙂
ZTE Blade L5 Plus – used the flash tool from this site as well as the ROM, rebooted phone after a successful flash, backlight comes on and that’s it. Soft bricked. Have tried redoing this a few times but get the same result. Is there anything else I can try before I decide to throw the phone in the bin?
Chris
What was the state of the device before you flashed it? Also, after backlight turns on does the bootlogo or boot screen show up?
phone still appears in Windows when switched on and plugged in, so there must be something i can do to it…?
No Scatter file for Alcatel One touch glory 2
Refer to this post – https://www.leakite.com/2016/11/download-alcatel-one-touch-glory-2.html
Product Brand is 4G+ and then on the sticker on the back there’s a number 02-A991-161482 and also T7P1482TC7A7C92. When i looked on Mobileuncle it says product board: sp6825c2_a10e_hy_x19_ch, i hope any of these are right? Thanks so much for your help, really appreciate it, its taken me 3 days now, and got nowhere.
I can’t find anything on the details you provided. China Tablets usually don’t have any screws binding the back cover to the board, should be easy open. If you can access the back then you’d be able to get extra details.
By the way, what actually is wrong with the device?
I can send you screenshots of the deviceuncle details, there are tons of info on the device if that would help?
I cant download google apps on the device to get app store and i cant get rid of some of the chinese apps and my camera is not the quality is bad.
I would like to have a full working android device where i can download apps.
It looks like an iphone but with android firmware, on the back it says Model A1633 FCC ID: BCG -E2946A ICxx9C
If that doesn’t help then I would have to open the back.
Thank you 🙂
Its says come from China
MAC: OC37DC67xxx
S/N: JTE8xxxxx200017xx
CMIIT ID: 201xxxx875
This is underneath the battery on the board.
#Modified by admin#
Hey Jess, let’s continue the conversation via email. Visit the contact page to send me an email with screenshot from MobileUncle.
Hey guys, I am super confused. I have done everything step by step and now getting to the point where I have to find the scatterfile.exe and there is nothing. Which version of sp-flashtool should i download. Cause i tried the latest one and the two before that. Please help.
Hi Jess!
You are actually supposed to run (or execute) flashtool.exe, then click on scatter loading and select a file that looks something like “MT6582_Android_scatter.txt“. It has to end in .txt extension. That’s the scatter file, not scatterfile.exe.
The scatter file is contained in the zip or rar file of the firmware you wish to flash, not in the flashtool folder. You need to extract all firmware content from the zip file before following the instructions here.
Let me know if you need further assistance.
Hi Collins,
I see! Thanks so much. Which of your custom firware would work for MT6797/SP6825 it says on the back of the china mobile phone A1633.
Thanks alot
If it’s a China mobile without branding, you need the board id to help you find its firmware. Can be found underneath the back cover.
If it’s branded, I’d need the brand name.
Mr Collins. thanks for your time.please help me with vfd301 ROM.that 408mb,and 300mb not work.someone have it with 766mb.but he looking for money first.and request to remotely access my computer.
sir, my G-tide e520 do not accepting their IMEI numbers now
(after flashing).
Hi, I recently purchased the UMIDIGI Z Pro off coolicool and after a week and a half, it suddenly started bootlooping and now it doesn’t boot past the android screen. I updated the firmware from 6.0.0 to 7.1.1 shortly after getting the phone. I tried factory resetting and eMMC flashing the phone but its stuck at its current state. I also tried using the SP Flashtool to reflash it to its original firmware but it didn’t fix the problem. Any ideas anyone?
Backup your important data, and reflash.
When flashing this time, format the device from SP Flashtool Format tab, or select Format + Download option from the drop down in SP Flashtool screen, then flash. This should fix the problem.
Hello
en mi doogee x9 pro me aparecio un menu en chino y ya no prosegui por que no se que opciones eran me podrias orientar por favor quiero instalar nuevamente la rom ya que mi telefono se apaga constantemente y se sobrecalienta
me muestra un menu en chino y no se opciones son por esa razon ya no continue
No entiendo. ¿Quiere decir que el firmware está en chino después de parpadear, o el flashtool muestra chino?
https://www.leakite.com/2017/01/easy-mtk-firmware-flashing-installation.html?xurl=http%3A%2F%2Fadf.ly%2F1YXrWz……………………SP Flash tool link is also not working….Please update the link….thank you……..
Fixed and updated now!
Dear Collins Edim please please send me the link for firmware for G-tide E83 please
No locations shows n the flashtool cant flash
Did you select a scatter file? Also, did you check if the Download Agent file is selected?
Please, i need of password to extrat de foldrs
Which other file do you mean? No file on this page is password protected.
I downloaded the vfd100 file but when I try to extract it is asking for a password, please help to have this file. Whats is the password?
I don’t think you downloaded the firmware from this site. The one uploaded here has no password, but the link was removed due to errors in the firmware.
Please request for password from where you downloaded it. They can better assist you with that.
Alternatively, you can download our password-free vfd100 firmware from this link – https://www.leakite.com/2017/01/vfd-100-smart-mini-firmware.html
What flag ware or Hawaii can I get to flash my techno j8
You need SP Flash tool and the stock rom.
Hello, I downloaded the package. I could not find the Map File or scatter file txt.
Appears tool dl image not found in may lenovo s650 after flashing
Did you get any error popup before flashing commenced?
what firmwareflash file that can be use to flash lenovo a3900
Download official firmware for Lenovo A3900 here https://www.leakite.com/2016/12/download-lenovo-a3900-stock-firmware.html
Are you able to access fastboot mode?
i need help… my y360-u61 dont boot…. i try every thing
may be try again by using different PC or USB cable or Port , Try by installing drivers and then flashing again
You will have to flash your device with its stock ROM. What's the device model exactly?
can i get the frp.bin file for tecno s1 and the scatter file only?
my mtk 6582 was a lg clone …3gb 32 gb rom version …… I flashed it with custom rom …now it turns on but remains on black screen …..plz help